0 Comment

Description. The UCA/UCA are fixed PWM controller for Off-. Line and DC to DC converter applications. The internal cir- cuits include UVLO, low start. Texas Instruments UCA Series Switching Controllers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas. Optimized for Off-line and DC to DC. Converters. •. Low Start Up Current (

Author: Kazrazilkree Mazurisar
Country: Gabon
Language: English (Spanish)
Genre: Video
Published (Last): 16 May 2015
Pages: 310
PDF File Size: 11.95 Mb
ePub File Size: 19.45 Mb
ISBN: 221-8-63811-491-3
Downloads: 85006
Price: Free* [*Free Regsitration Required]
Uploader: Kazrataur

Jan 10, 4: And if the device starts to work in intermittent mode, this source will simply burn.

HTTP This page has been moved

The open circuit voltage is adjusted with the already existing potentiometer, this shall be less than the voltage value of the output capacitor. May at Theoretically push the diode to the voltage divider, then it will be shown.

Rsense would be 4W at uc8343a. These ISRs have a maximum output current of 1. If you would like to know more, look in the D amp-Forum over.

Pin numbers refer to DIL package only. Jan 17, 6: However, during the term of this Agreement ON Semiconductor may from time-to-time in its sole discretion provide such Support to Licensee, and provision of same shall not create nor impose any future obligation on ON Semiconductor to provide any such Support. This thread has been locked. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right.


It is to make sure that the power, caused by thermal drift, specified does not exceed the operating current of the manufacturer.

10/30/50/100W LED application driver (UC3843A)

At a minimum such license agreement shall safeguard ON Semiconductor’s ownership rights to the Software. I am waiting a few of them and when I get them and make the changes I will tell you how they did it.

July at Several parts need to get changed. BOM, Gerber, user manual, schematic, test procedures, etc. This site uses cookies. Notwithstanding any terms to the contrary in any non-disclosure agreements between the Parties, Licensee shall treat this Agreement and the Content as ON Semiconductor’s “Confidential Information” including: October at 9: Failure by either party hereto to enforce any term of this Agreement shall hc3843a be held a waiver of such term nor prevent enforcement of such term thereafter, unless and to the extent expressly set forth in a writing signed by the party charged with such waiver.

Do you also need Power Factor Controllers? This low-cost, industry-standard IC contains the required protection features and d Doc. No license, either express or uc384a3, by estoppel or otherwise, is granted by TI. This results in a higher control loop stability, also the feedback compensation to uc384a interpreted high-ohmig.

I also found one interesting fact. The use of an external N-Channel MOSFET allows the user to adapt the device to a multitude of applications depending on system requirements for current and dropout voltage.

UCA datasheet – SMPS Controller

Nothing contained in this Agreement limits a party from filing a truthful complaint, or the party’s ability to communicate directly to, or otherwise participate in either: A small discrepancy I noticed though: The output uc3843q is controlled via a variable resistor. The device is powered by a powerful 12 volt battery. The original is k 1k 10m here.


Locked Cancel Do you have another question? Jan 17, 1: January at TI is a global semiconductor design and manufacturing company. Licensee agrees that the delivery of any Software does not constitute a sale and the Uc3843x is only licensed. Because the circuit with R8 measuring shunt 10 mohm is a bit on the low end, it is, to replace it with 50mOhm. I do not change the input voltage during operation. This Agreement may be executed in counterparts, each of which shall be deemed to be jc3843a original, and which together shall constitute one and the same agreement.

Also why do you use 9V for the voltage regulated one and the Vref for constant-current one? Within 30 days after the termination of the Agreement, Licensee shall furnish a statement certifying that all Content and related documentation have been destroyed or returned to ON Semiconductor. Jan 10, 3: I would suggest increasing C3. Supply Voltage Low Impedance Source. Hellocongratulations on your posting.

Nothing in this Agreement shall be construed as creating a joint venture, agency, partnership, trust or other similar association of any kind between the parties hereto. The SO package has separate power and ground pins for the totem pole output stage. I built the light as I needed a flood for use on forest uc3843s farm land that had a long switch on time from a ah 18v battery Regards steve.

How to fix it? The regulators are intended for use as post regulators and microprocessor supplies. In reply to Benjamin Lough:.

For proper operation, it is essential that the output voltage or voltage of the LED at the nominal current is greater than the input voltage of the Step-Up Converter.